Recent Solution

Nokia 1616 dialed calls not showing problem solution

Problem: Recent dialed or received calls not shown in the directory.Solution: Change this diode. Full flash with j.a.f.

Should be the cause of deprecation. When the all calls are (Incoming/out going) unknown. The cell number or massage is hidden and the owner is unable to see it. This is the repairable issue in the Nokia 1616 cell phone.

Solve the issue of dialed calls not showing in the recent dialed up number directory.

Troubleshooting guide:

Behind it, May be there are some other issues. But in my lab. I have faced it from the faulty diode polarity. The tricks of shoot the issue. Dialed calls are hidden and not shown problem. We are going to fix it by steps.
Keep in mind, The timer need to collect the recent activity on the Nokia-1616 cell phone. If the real time clock or software TX-RX or any required connection from the flashing chip. Missing or shorted. This error may have accorded.

  1. Clean the all PCB with petrol or carbon tetra cleaner.
  2. Pick this diode from the Q-E-4 old cell phone of china made. 
  3. Change with the red circle mark part.
  4. Hard reset of flash with J.A.F.
Hope ! Problem is fixed. In the condition of fail to fix this issue. Please fell free to contact me at my G-mail address: shahidabbas2001@gmail.com. I am waiting  your input for further information at the given topic. The all tricks are given on this blog. After checking me into my lab. Some time different situations should apply to fix it. In many cases i recommend to you. Please be careful during working on the listed tricks. Handset may harm or dead from a little mistake. The flashing chip is major cause but the points are controlled from this diode. Stay in touch for more from our side. Follow from the right side of bottom at the end of scrolling.

Thank you so much for visit/read this article.

Q mobile M-95 slow charging solution

Why this problem created in Q mobile m-95 cell phone.

Due to used unqualified battery charger or by shorted USB connector. The problem of battery charging is so slow or not storage in Q mobile m-95 cell phone. Today i am share with you, Fix the issue of slow charging in this cell phone brand.

Problem: Slow charging, Battery not storage, Charger not connected, Shorted cell phone.

Solution: Check and clean USB jack, Attach the 4 volts zinner diode.

Q mobile M-95

Troubleshooting guide:

First thing first, Always use the original charger. The voltage regulation parts are so cleaver in this brand to boost up the life of cell phone. Many time i see the handset is faulty by used the low quality charger. So i think the original charger should supply the correct rating of charging voltages to the cell phone.

Another possible reasons behind this issue. May be the USB connector is carbon of tetra infected. Any way let we start to fix this issue by steps.

  1. Clean the USB jack and use the original charger. If possible to auto control power supply with the current used display. Please connect the cell phone with it.
  2. Check the battery terminal positive volts with out inserting the battery.
  3. Low current at the charging out point is the major cause of this problem.
  4.  Connect the 4.5 volts diode into the charging to battery terminal positive point.
Hope you like this simple but most useful trick to fix the issue of slow charging in Q mobile M-95. For more inquiring or details fell free to contact us shahidabbas2001@gmail.com.

Nokia lumia 630 power switch button ways

Solved: Nokia lumia 630 power switch button ways

Problem: charging ok but power key not working. Missing on off key points.

Solution: Check and clean on off key. check and trace missing points. Jumpering on missing points of power on off key.

Troubleshooting Guide for lumia 630 missing power key points.

Hello! we are going to shoot the issue of missing power key points of a Nokia lumia 630 cell phone. As you know every electronics device have power key. To alive or sleep the device in most electronics devices have on off switch. In the cell phone Nokia lumia 630 power on off touch key is on the side of panel. In condition of missing power key handset did not power on. At connect the charger the charging logo show on screen perfectly but when pressed the power key. There is no response for powering the handset.

Fix the issue of lumia 630 did not power on (Cell phone is dead)

Let we start to troubleshoot this issue by steps. Keep common testing before jumping directly on the board. May be there are some more differents problem occurred behind this issue.
  1. Clean the power key switch button.
  2. Change the power key touch button.
  3. Remove power key check the missing points.
  4. Make jumper with jumper wire as picture shown above here.
  5. Handset power key points are ok but set not power on. That is not power key relate fault.

  • Fix the dead cell phone lumia 630 if power key working fine.
There are one or more reasons behind this issue. Power key points and touch button working fine. Handset is showing charging logo at screen perfectly. Let we start by steps tracing this fault.

  1. Connect your cell phone lumia 630 via usb with computer / laptop.
  2. You have access in the storage media devices.
  3. Download NokiaSoftwareUpdaterSetup_EN_US.
  4. Update software of Nokia lumia 630 cell phone.
No success all above tricks applied after handset dead and same condition.
Here are more ways to fix this issue. Clean all pcb and normal heat power chip of the cell phone. Be careful! Overheating may harm your cell phone will be completely dead. In some situations Power key showing the polarity by capacitors. Remove power key line capacitors. Try again by jumpering. Trace the power key lines from on off switch to power key chip. May be there on mother board of lumia 630 of off diode or resistance is broken or shorted. Check and trace this fault.

Almost done!

Hope you like this post for the problem of Nokia lumia 630 power on off button not working. On the phonetolls there are many other manual troubleshooting guide are waiting for your visit. Please mousing on the home button or use search box for more solutions.
I have creating a new website for your help with many online free course by my coursework series. Please visit my website c4dprime.com.


Nokia 110 sim ic jumper ways

Troubleshooting guide for Nokia 110 insert sim issue

Problem: insert sim, sim not valid, sim jacket broken links.

Solution: check sim jacket missing points, make jumpers.

Fix here for Nokia 110 insert sim problem.

Learn how to fix the issue of Nokia 110 insert sim. Missing sim jacket points and there is no polarity on the check meter. There are two sim trays with the series connections from the sim controller chip. The sim one tray must enabled by sim inserting to understand this issue.

Follow these instructions.

  1. Insert sim into sim tray one.
  2. Insert sim show on screen but sim is inserted.
  3. Check sim side and jacket side connections. 
  4. Clean both connections.
  5. Heat sim controller chip with normal heat.
  6. Check the missing jumpers at sim holder.
  7. Make only at missing point jumper with jumper wire.
  8. Check battery terminal center point of BSI volts.
  9. Clean all PCB normal heat main chip.
Almost done!
Thanks for visit here on phonetolls. We provide lot of solved solutions for mobile repairing. For more information about the mobile repairing please visit home page or use search box.


Top best android auto call recorder software

Record your calls get call recorder software easy for android

The default option not available in the most common cell phones. The external applications are available for auto call recording. Android file type .apk is the known as android application. Every file that extension is .apk. can run on supported android platform. The android application did now run on windows or another platform.

Why Auto call recording software for android cellphone

To record the instant calls of your sim numbers. The auto call recording is an optional setup. There are two types to get this option in android cell phone. One from the buildon option if available in your android cell phone. Active it the configure with the essential setup as your need. The other last option is get the auto call recording software from the google play store. Run application setup after download complete. Active and configure the application setting as your need.

Top Best auto call recorder software. 

In the category of auto call recorder software. Top best collection is available by numbering here.
  1. Total Call Recorder (TCR) is one of the best all around the world. For the silent switching during connecting calls gives it all stars. 
  2. All Call Recorder is the best for call recorder. User can set up easy and working auto when call connection successful.

  3. Best Call Recorder is the free application that work with optional incoming and outgoing calls. 

How to use auto call recorder software.

From the application icon. User can open/run application in the android cell phone. When application is open. There are some optional setup required. For the save recording as directory. Set up the root of the auto call recorder software. After recording user can get the recording file from that directory. Best for the root please save in memory card location your all auto call recorder files. 

Some software may have ask to setup automatic delete old call recording for saving the space of storage media. Activation have a beep when call connection successful. With beep that is not good for the auto call recorder software. 

Almost done!

Thank you so much for visit today on phonetolls.blogspot.com. I have a website for online free courses. Please visit the link for more information. https://www.c4dprime.com/

Nokia 300 touch screen ic jumper ways

Troubleshooting guide for Nokia 300 touch screen issue

Problem: Touch screen not working, Touch is ok but problem occurred.

Solution: Heat touch ic, Change touch ic, Remove and make jumpers.

Troubleshooting guide.

In this condition you have try every trick. Change with new touch. The touch is ok but problem still and touch screen not working.
This problem comes with due to water of old handset. The real issue of this problem. The touch screen did not work. Touch screen connector points are show perfectly at check meter.
  1. Check The touch screen first. To checking the touch screen. There are four pins. At the probe two by two connections are ok. 1x4 and 2x3 are the show with polarity. Now attach meter probe with 1x2 points of touch side connector. Push your finger on the touch front. If there is some polarity showing on the check meter. This mean touch rx is working. Same test repeat with other two pins. The polarity is showing. The touch is working very well.
  2. Heat the touch ic. To trace the touch location on the motherboard. Please see above image here. The touch place is showing without touch ic by jumpering. Be careful by heating you have experience for that job. 
  3. There is no luck and touch ic connections are missing. The final solution is remove touch ic and make jumper directly with jumper wire. The jumper diagram is given in the above image here.
  4. For the jumpering you need very sharp bit. I recomend you please use the heat gun iron with the voltage regulator. 
  5. Almost done!
Thanks for watching/reading out this guide. Hope you like this post. Here on this blog i have posted many solution for mobile repairing with the article and troubleshooting guide. Please visit this blog for more fixing your cell phone issues.
Bye Bye!

old cell phone buying guide

Tutorial about | Old cell phone buying guide

Subject: In this article i want share some information about, old cell phone buying guide. 
Sources: Online seller and comparing websites.
old cell phone buying guide.
Ideal deal with old / used cell phone demand care about what is the important to check in cell phone at the buying point. In the market or personal many peoples wants exchange or sale there cell phone. In the brain there is only one thought, Is this cell phone all correct and no problem with its. But by troubleshooting you can test or check some general issues. Here are the ways of problems that can identified by troubleshooting.

  1. Original or fake, From the software information or behind the back side under the battery. Found the model number of cell phone. If Cell phone is Nokia company, type at keypad *#06# the see the imei number on the screen. In the android this option is available in the setting menu at the end of menu with the name of about phone etc. Fount the brand model number and keep in mind.
  2. Olx, For the price with in minimum and specs of the brand model number are available on the olx adds. 
  3. Sim, Signal, Charging, Mic, Ringer, Ear phone, Battery storage, Battery is not pregnant, conform the listed problems are not found in the cell phone.
During making call signal quality is good. Hand set is not shorted or water damaged. Some time at the battery used on media the battery empty and handset getting power off. In this situation please do not purchase that cell phone.

  • Check the display quality, LCD is original and touch is working perfectly for android or touch cell phone.
  • Check the power use in the info graphic at battery use. Which stage of cell phone is used the max battery.
  • Play a heavy game at the cell phone then check the cell phone is not heated.
Hope you like these simple tricks from my side. For more information you can email me at shahidabbas2001@gmail.com. Thanks for reading out this post. Please share with friends on Facebook and twitter. 

Complete Mobile Repairing Guide

Logo.pngHello! All members and visitors. Today i want share anything with you. That i know about Cell phone Repairing. If you are searching good based blogger for learn how to repair cell phone at home the you are right here. Happy to say after a long waited i have plan for teaching about cell phone repairing. Hope you enjoy these some tricks and techniques. As you know my wish, "Provide you a rich and unique contents" As my best knowledge base. I strongly request you to comments about my work. For improve my job i appreciate your suggestion. Thank you for visit "Let we stat"

Learn At Home, Complete Mobile Repairing now so easy

Before start our work i want share what kind of tools you have required for cell phone repairing. If you have a shop then no need any extra tools. But for new student must have access the following tools for testing and tracing cell phone faults.
  1. Solder wire / jumper wire and and heat gun with soldering element
  2. Board griper and tools kit 
  3. Ct or petrol, Old cell phone PCB and some of accessories .e.g. charger, data cables software flashing devices, computer and internet
  4. Old cell phone dead motherboards for some parts replacing e.g. resistance/capacitor
  5. In the parts box basic most running parts of mobile phone e.g. mic,battery terminal,display(LCD),ringer,speaker,battery connector,charging base,sim jacket
  6. For Copying memory card, You need card reader

 Cell Phone Categories by series are following:

In the market many cell phone models comes with different names. Every brand are labeled e.g. Nokia,Samsung,Q-mobile etc. After the cell phone name on front / behind the batter / on the inner there have model number e.g. Samsung Galaxy j-700 f. Every cell phone is comes in market by series, Some of most common series are following:


S-40 Series (Without java and application)

Some have java but many are without java. (Java is the software based facility that provide play games or software's) For example Nokia 1100,1110,1212,c-1 and other small price handset are comes in this categorize.

S-60 Series (With java or without java) 

After success s-40 series Nokia have lounge s-60 series with more rams and user friendly browsing software. Nokia is the one of the best for easy and power full user friendly software, As known the Nokia logo hand set is the sign of quality and guaranty. In this categorize some most popular handset from Nokia company comes in past e.g. Nokia C-5, C-3, x-2-02 etc. (In these latest brands are comes with WiFi)wireless connection.

X series (Implicated WiFi, 3-G, 4G and Touch panel)

Is the series with WiFi and internet explorer for communication friendly and speedy some have 3-G or 4-G band.

Windows Series (Implicated WiFi, 3-G, 4G and Touch panel)

Latest by Nokia Company. Nokia introduce Windows cell phone with ios support implicated. Nokia Lumia is the best in this categorizes. Nokia 430,720 are my fave rte.

Android Series (Implicated WiFi, 3-G, 4G and Touch panel)

In these days this series is no-1 in all around the world. Many application are available and this series is touch and non touch used in many communicative devices. Tab, Note, Cell phone, Television, Camera, and many latest devices comes in the market with android version. 

Understand, CELL PHONE PCB

Home for electronics parts, Where the all parts are paired by tree. There on every PCB or motherboard many parts are by series connected each others familiar. They called integrated in the following categorizes:
  1. Verb (Major parts on PCB) Example: IC (Integrated circuit) is the verb part of PCB
  2. Non verb (Helping Parts for major parts on PCB)Example:Resistance and capacitor are the helping parts for IC (Integrated circuit) on PCB
  3. Fuse and jumpers are for safety use in every electronics devices
Every Electronics and electric device use a board for home Parts to connect each others. On the board connection plate should help by lines to connect as a series all parts. Fiber and cotton mixer plate, Assembled for long life and hardness to get non polar polarity for connection plate.
  • Resistance (Most common use in every electronics/electric devices)
Every cell phone use current from battery as a power source. Battery current ampere and volts are important for cell phone. On the mother board of cell phone there many parts which are working by series. Some have need 3 to 4 volts and some have need just so low voltages. Some frequency stages can use resistance for resist. As the name of Resist, From high to low convert parts on cell phone mother board called resistance. In the Television the value of color coding may help to find expect value of  resistance. Here are color coding for resistance:
  1. Black
  2. Brown
  3. Red
  4. Orange
  5. Green
  6. Blue
  7. Gray
  8. White
Up Numbering can not help in micro parts like as resistance or capacitor, There on micro parts the only one color can help for resistance, BLACK is the symbol for resistance. Size of Resistance should control capacity. So the main thing to understood in this case, We have 3.7 volts from battery. We need low volts from 3.7 to 1.5 to supply some major parts, e.g. IC. To solve this issue every cell phone and electronics devices use Resistance. When we check any resistance on the multi check meter there are dial shows some ratings about resist. 

  • Capacitor (This is the most commonly used in every electronics/electronic devices)

Capacitor can store current for some moments, Some time during first startup cell phone or any device need full power to serve there work. For example Cell phone is powering on and searching signals and found every parts on PCB, There is full bright on display some or many applications are tuning together at startup. The all capacity of used for current is very high. You can check on auto voltage supply regulator display the pixel of used power supply are gone to 69 or above points. But when all processing of cell phone should complete and display lights are off from LCD and Keypad. The handset is off line and there on supply display show very low current in use. Cause for that the some very essential processing is running but most of the other processing should finished for max battery timing automatically. 
At the testing pros Capacitor there have no rating for long time show a dial pad on multi meter.
So after read all summery about capacitors, Now we collect some information to find on cell phone motherboard. Brown or white or black color is the symbol for capacitor. Brown is used for Stored current. and others colors are for frequency cycle control's. So the last word about capacitors are used for filtering and storing currents in every electronics and electric devices. In the cell phone every parts are micro categorizes.
  • Fuse (This is the most commonly used in every electronics/electronic devices)
In faulty this parts, "FUSE" the device completely dead and there is no response on power in from fuse one side to other side. For the safety of the device, the Fuse is the connection of positive volts supply to a board. As a wire the fuse system is used most  commonly. For example to understand:
  1. From the main supply, Battery / charger is over current the fuse may have harm.
  2. From the water or rain shortage current, Fuse may have harm.
  3. From the old water damaged handset, Fuse may have harm.
  4. From the opposite connection of current e.g. negative probe connected on positive current, Fuse may have harm and device getting dead.
  5. From the shorted parts of cell phone, Fuse may have harm.
  • Resistance (most commonly used in every electronics/electronic devices)
For saving the energy, This parts is the most commonly used in every device of electronics. On the device motherboard there are many parts with series and parallel connected each other one by one. The all parts of a motherboard have a different rating of a voltages. Their on battery terminal the voltages of rating 3.7 volts but the IC or transistor need an 1.5 volts, To solve this problem the resistance used is very common in positive or negative points.
  1. Resistance should not boost any current from in to out points.
  2. Resistance can gain only high to low current.
  3. Resistance is the connection part of the pcb from one to another point.
  4. Resistance rating is by size and colour valuable.
  5. In condition of faulty this part hande set may have faulty.
  • Transistor (most commonly used in every electronics/electronic devices)
Base, Emitter and collector are the the legs in the every transistor And the category of PNP,NPN for the following:
  1. PNP (Base,collector,emitter) in this category the positive volts in on base point.
  2. NPN (Collector,base,emitter) in this category the positive volts in on collector point.
  3. It can boost or handle volts and frequency cycles.
  • IC / Chip (Integrated circuit)
As a name integrated, Many electronics parts in one chip. The major part of cell phone processing unit. from the solid state physics converted some stages of electronics devices e.g. cell phone, camera, tv, computer into a one chip. The processor is a home of multi chips. In every cell phone the main chip (Processor) did not work without some helping parts. See this short menu of the chip for working:
  1. IC: In the cell phone PCB, the major part is a main chip.
  2. Helping parts e.g. resistance,capacitor and transistor are the pre versions of main chip.
  3. Some cell phone used a single chip with build on flashing, signal, Sound etc. but some have independ chip for the signal, flashing and sound etc.
  4. In condition of faulty chip the chip should warm up after few second power on the cell phone. This chip is warming up from the many reasons, Shortage stage of inner in chip / outer on PCB. Example: Main chip is warm up, In the main chip circuit may be the charging,signal,sound or any stage is faulty for cause of warm up the chip. 
  5. From outside the supply is over current, during processing some helping parts may have harm. For the conform is their main chip is faulty, Please be carefull. Trace or check before replace or remove main chip. May be some other reasons are involve to heat up the main chip. e.g. ringer connection are shorted with ground directly.
  6. Power chip, Controller chip for the supply. If faulty, the Handset did not power on or shortage and battery timing is so short.
  7. Signal chip (PA), The signal stage controller chip. If faulty, there is no signal or weak signal in cell phone.
  8. Flashing chip (ROM), Storage drive for cell phone software. if faulty handset did not power on, Some time flashing the lcd and some time hang on LOGO.
  9. Sound chip, Sound controller stage. if faulty there is no sound in ringer.
  10. Bluetooth chip, BT Communication chip controller. If faulty there is no access in search neighbor bluetooth device.
  11. Display chip, Display controller for lcd data. If this chip is faulty, there is no display,scrambled display, white display or blank display on the LCD.
  12. Keypad Chip, Keypad controller chip. If faulty there on keyboard some or all keys are missing. Keypad did not work correctly.
  • What kind of components that should jumpering by diagrams
Some time the faulty chip /parts are not available in the market. Therefor, With the diagram of jumpering we should make directly jumpers via jumper wire on its connections. Here are the list of those who should jumpering directory of some have without changing with new one.
  1. Keypad chip (Make directly jumper on missing keypad tracks from one by one)
  2. Signal chip (Low signal problem occurred by using the jumpering in some cases)
  3. Fuse (Burning or missing fuse we should directly jumpering from one to another point)
  4. Resistance (We can direct some types of resistance on the PCB)
  5. PCB broken links (From one point to another point we can make a jumper)

ANDROID CELL PHONE HARD RESET WAYS

When cell phone start hanging, Slow on speed or any application issu. You need to an hard reset your cell phone for the default settings. There are some differents ways to do this action. Here are some hard reset tricks for help to reset your cell phone.
  • Hard reset cell phone from the setting menu (Factory setting)
In the every cell phone have hard reset option with the differents names. In the most common this option found in many cell phones on the setting menu. Found the factory setting, hard reset or reset all data from you cell phone then follow these steps:
  1. Factory setting
  2. Give the password 
Default passwords of many cell phones

  1. 12345 (Nokia)
  2. 1122,1112,1234,0000,2233 (Android / China)

  • Hard reset cell phone from the power on (Factory setting)
In the android cell phone the software hard reset option can run from the power on to get the default settings of the cell phone. Some time handset still with pattern lock, Google account lock, Hang on log or slow speed. In this condition you need to hard reset cell phone from the power on. Before start the tricks of numbering here please power off your cell phone. To power off disconnect the battery and insert again. If battery is build in the casing then please power off key press and hold till them the handset getting power off.
  1. Hold on volume up key then press power on button
  2. Hold on volume down key then press power on button
  3. Hold on both volume up and down key then press power on button
  4. Hold on Home plus volume up key then press power on button
  5. Hold on home plus volume down key then press power on button

  • Hard reset cell phone with the flashing device (Factory setting)
In the condition of no access in reset from the software or power on key the last option is "Hard reset" cell phone with the flashing device (Jaf, volcano, flasher) etc. To reset with flashing device you have the direct access to the cell phone flashing memory (ROM) by the RX, TX and battery power points. You can connect the device with your cell phone usb data cable, Device flashing data cable or directly with jumpering on the TX, RX points at the PCB.
  1. Connect your cell  phone with the device data cable
  2. Open flashing software of the device that you have set up in your computer or laptop
  3. Go to the factory default panel and click to continue
Keep in mind during hard reset your cell phone, There are two differents options. One with erase all data and second with only settings. Chose as your need to solve the problem. All Data of the cell phone should eras in complete factory settings. So if the possible for you please before start the job of hard reset "Backup your instant data" and contacts.

DISPLAY PROBLEM AND THEIR SOLUTION

Due to rain, water damage or missing broken links are cause of this problem commonly in every cell phone. The broken display solution can solve only with new or working display. But in many time from the troubleshooting of cell phone PCB points i solve these problems:
  1. White display (Change LCD or check lcd connection from the connector)
  2. Blue display (Check connector)
  3. Scrambled display (Check connector from the both sides LCD/PCB)
  4. Blank display (Check connectors, Change LCD)
  5. No lights on the display (Check LED lights, Volts and connection)

SIGNAL PROBLEM AND THEIR SOLUTION

When signal stage is faulty the cell phone signal should gone or low. You can not make a call to another cell phone or during call the sound like as fax machine. In the many cell phone i see the signal baar with the one or two points. In this situation, when the cell phone our range from the tower. There is no signal. Anyway see here are the most commonly signal problem solution:
  1. Low signal (Check antenna)
  2. No signal (Heat, change PA)
  3. Signal OK but call failed (Check RX or TX of signal chip or change signal chip)
Many cell phone signal chip should jumpering, But the long range distance signal problem occurred with jumpering of signal chip. So the first choice to solve this issue please replace the signal chip with new or working.

INSERT SIM PROBLEMS AND THEIR SOLUTION

When insert sim option show on the screen of cell phone after inserting sim in sim tray. This mean this sim stage is faulty of the cell phone. Some time the sim chip is broken cause behind this error but many time i see this problem in sim jacket or connection. So here are the troubleshooting guide for possible solution of insert sim error.
  1. Check / change the sim side and cell phone side connection (Both clean and scratch for the carbonyl issue)
  2. Check the sim jacket points (One point is always ground and in many cell phone the one point is empty) If missing any connection please make jumper.
  3. Check Sim chip (Some time broken or carbonyl chip connection are the major cause) Change the sim controller chip, Heat or make jumpering on it.
Final if no luck, I thing the processing chip points are missing that are routed to the sim controller chip. So be careful in this condition. Before troubleshooting the cell phone. Ask the customer for dead approval. After that heat the main chip or trace the missing jumper from the main chip to sim jacket or sim controller chip points.

CHARGING PROBLEM AND THEIR SOLUTION

Charging error starts in many cell phone from the USB bad connection. There is no option at connect the charger on the screen. But many time i see the charging volts getting wrong rating on the positive point of battery terminal. Here are the possible solution of charging problems:


Nokia 3110-C No Light jumper.

 With article and troubleshooting guide solution for Nokia 3110-C No Light fault.

Problem: Dark display, Missing LED, No voltage on Positive point.

Solution: Change LED, Check 3.7 to 4 volts on LED positive point, Make jumper.
  • Article on this topic.
There is no bright in display, Screen OK but LED's did not working. In this cell phone Nokia 3110-c due to water or carbon some time display lights may harm. Because this is a old cell phone of a Nokia company. As you can see diagram below here some red lines show you points for repairing this issue. If display is dark of your cell phone you can not see any thing on display in darkness. Success of Nokia cell phone is separate parts for all stages is a hidden truth. For example if light stage is faulted you can repair this problem by troubleshooting light stage. Today's in china and other brands use single chip CPU with build-on all stages into one chip. If lights or sound problem is showing you can not repair easy. Any way Nokia is the most of popular in cell phone technology. If your hand set Nokia 3110-C is a display dark problem. You can repair this issue by following our troubleshooting guide. To repair compactly don't follow blindly this diagram bellow here. Before start your work please see our troubleshooting steps. There are many other reasons behind this problem.  


https://phonetolls.blogspot.com/
Nokia 3110-C No Light jumper.
Thanks for checking out this Solution. Phonetolls.blogspot.com contents provide include dozens of cell phone additional articular and picture help with hardware / software troubleshooting guides for you. Support us  like and connect with this blogger for latest newsletter please follow me, Admin Shahid Abbas.
    • Troubleshooting guide.

    Nokia 3110 classic cell phone is an old series of S-40. This cell phone working over all very good. But due to water / over current or missing connection lines may have a reason of dark display. Some time missing bulb current or damaged bulb of screen is a major cause of this problem. As you can see diagram above many red lines. To understood this diagram you need some checking on motherboard. Here are some useful steps for repairing this problem.
    1. First check LCD connector LED's Connection points. Up side of connector pin NO-2 is positive and down side pin No-2 is from keypad LED's.
    2. Check 6 pin ic and short 2 points.
    3. After this step check light ic and coil.
    4. Check on coil positive current from battery connector positive point.
    5. If there on a coil is no positive current make a jumper from battery terminal positive to coil point.
    6. Open LCD background strip and remove on LED. Make jumper on Only one LED same as diagram.
    7. You can use these jumpers for 2 LED's.
    Warning! During working on this trick cell phone, accidentally may have harm faulted dead or stop working. We are not responsible - Please read our Privacy policy for report and disclaimer issues. Goodbye!
    Ad c4d prime

    Nokia X 2-02 Dead cell phone problem.

     With article and troubleshooting guide solution for Nokia X 2-02 Dead cell phone problem.

    Problem: Water damaged, Dead cell phone, No power on, No charger response.

    Solution: Remove R-15 resistance, Full flash software, Check battery connector.
    • Article on this topic.
      Hello! welcome back again here. Today here in this diagram you can solve dead cell phone problem. Last day i received a cell phone in complain. First cell phone come on my shop with fully shorted problem. At supply connection supply power of automatic. I solve this problem from Changing Multimedia controller chip. After 7 days same handset come back again with dead no power on problem. When i connect cell phone with external power supply. There is no power in pixels. On cell phone pixels at power supply is 1-2-3 points. But this cell phone Nokia X 2-02 is dead and no response. I search this problem on internet. Here are some steps that i will try to solve this problem.
      • |First clean PCB normal heat with hot air.
      • Check battery connector power on main power controller chip. There is no power on Chip brown capacitor. 
      • For trouble shoot more this problem please read our trouble shooting guide.
      Https://Phonetolls.blogpsot.com
      Nokia X 2-02 Dead cell phone problem.
    Thanks for checking out this Solution. Phonetolls.blogspot.com contents provide include dozens of cell phone additional articular and picture help with hardware / software troubleshooting guides for you. Support us  like and connect with this blogger for latest newsletter please follow me, Admin Shahid Abbas.
      • Troubleshooting guide.
      When i check and traced a positive volts on PCB main parts, There are low voltages. Battery 3.7 to 4.0 volts not reaching on power chip. I Thought this hand set is compactly dead. But one question is in my mind, How can this cell phone dead. I did not accept this and at all i decide to trace this fault. Here are some most important steps for solving this issue.
      1. Check and clean battery connector. Clean Battery side connections.
      2. Connect charger if charging logo not showing Clean charging base or check charger.
      3. Connect cell phone with power supply, There is no on off points.
      4. Check on off key, Key is working OK.
      5. Check R-15. This is a fuse able resistance. There on check meter full dial show at x-10 dial switching.
      6. Change this resistance with other working parts. You can pick this resistance from another old Nokia cell phone motherboard.
      7. This solution is 100% tested by me. Full working solution.
      Warning! During working on this trick cell phone, accidentally may have harm faulted dead or stop working. We are not responsible - Please read our Privacy policy for report and disclaimer issues. Goodbye!

      Ad c4d prime

      Q mobile 115 hang on keypad solution.

      With article and troubleshooting guide solution for New latest solution for Q mobile 115 hang on keypad fault.

      Problem: Keypad not working, Hang on keypad, Hang on main screen.

      Solution: Clean keypad, Remove USB shorted.
      https://phonetolls.blogspot.com/
      Q mobile 115 hang on keypad solution.
      • Article on this topic.
      This new cell phone Q mobile 115 is design low range price. Available with small size screen, Multimedia, Dual Sim, Camera. This cell phone is a Ladies first choice, because its size and weight is close. On this cell phone PCB main chip is build-on with charging stage, Audio stage and Sim controller stage. Very fast with ram for video player. Small size of display give it a long battery life.

      Thanks for checking out this Solution. Phonetolls.blogspot.com contents provide include dozens of cell phone additional articular and picture help with hardware / software troubleshooting guides for you. Support us  like and connect with this blogger for latest newsletter please follow me, Admin Shahid Abbas.
      • Troubleshooting guide.

      Ad c4d prime
      Today on my shop Q mobile 115 come with hang on keypad problem. I solve this problem with these tricks, That i want share with you. After changing USB / Charging base from no technical hands. Charging base two points shorted with key pad 0,# keys. At center points of these keys i check with check meter. I found these both keys are shorted with charger in point on PCB. When pres 0 key or # key on keypad hand set hang. Some time with out pressing any key at display hanging problem. When i test 0 and # key by check meter, These both key are shorted with USB Rx and charging points. I solve this problem with these tricks.
      1. Remove charging base. Clean charging base points. 
      2. Main reason of this problem point 1-NO and 2-No on charging base is shorted, Resold 1-NO and 2-No points. Rx And TX may have harm when shorted with charging in points on charging base. 
      Warning! During working on this trick cell phone, accidentally may have harm faulted dead or stop working. We are not responsible - Please read our Privacy policy for report and disclaimer issues. Goodbye!
      Ad c4d prime

      Cell phone sound like a fax machine fault solution.

       With article and troubleshooting guide solution for Cell phone sound like a fax machine fault.

      Problem: In earpiece/  Ringer / speaker sound like a fax machine, Water damaged cell phone.

      Solution: Clean cell phone motherboard, Heat cell phone motherboard.

      https://phonetolls.blogspot.com/
      Due to water damaged cell phone distraction voice.png
      • Article on this topic.
      http://phonetolls.blogspot.com/Hello! Hello again Hello, You can not understand any audio from Earpiece / SPK (Speaker, Ringer). Reason of this problem Cell phone sound like a fax machine. Some time when we touch cell phone these voices may loud. Many time this problem created during loud / open voice. At multimedia player in many china cell phones audio same as horn or whistle audio. I face this problem many time on my lab during my job. The best solution for this problem, Clean and heat Main ic, (When volume up over 3 points this problem show in china cell phones). Here in this single post not possible explain all issues of this fault. Here is reference link for complete information about this problem please for more visit this link, http://adf.ly/1JrzBa.

      Thanks for checking out this Solution. Phonetolls.blogspot.com contents provide include dozens of cell phone additional artical and picture help with hardware / software troubleshooting guides for you. Support us  like and connect with this blogger for latest newsletter please follow me, Admin Shahid Abbas.
        • Troubleshooting guide.
        There are many reasons behind this error Cell phone sound like a fax machine. There are two kinds for troubleshooting this problem (Hardware, Environmentally). Due to water damaged some time handset working well but bhind sound related chips on motherboard carbonyl connections are major cause of this issue. Let's troubleshoot this problem these two types by steps.

        Hardware repairing for Cell phone sound like a fax machine fault problem.
        • Open cell phone casing exit PCB from inner.
        • Clean with CTC (Carbon tetra cleaner / petrol).
        • Heat cell phone with hot air (Heat gun /  dryer machine). 
        • Note before heating, cleaning Remove these parts from motherboard if possible (Camera, LCD), Be careful.
        • Power ic, Signal ic, sound ic stages of cell phone motherboard are very important for this problem give extra time on these stages.

        Environmental issues for Cell phone sound like a fax machine fault problem.
        • Poor wiring.
        • Weather.
        • Electrical interferences.
        • Other phone devices.
        • DSL.
        Warning! During working on this trick cell phone, accidentally may have harm faulted dead or stop working. We are not responsible - Please read our Privacy policy for report and disclaimer issues. Goodbye!
        Ad c4d prime
         
        Copyright © 2013. Phonetolls - All Rights Reserved
        Template Created by C4D Prime | Published By C4D Prime